Skip to main content
CO
βš™οΈ

Well Pump Repair in Colorado

Avg. $300 - $3,000 · As needed (pump lifespan 8-15 years)

2
Cities
$300 - $3,000
Avg. Cost

Well pump repair services address the mechanical and electrical components that bring water from your well into your home. The submersible pump β€” located deep inside your well β€” is the hardest-working component of your water system, running thousands of cycles per year to maintain household water pressure. Common pump problems include motor failure (often caused by electrical surges or sediment wear), check valve failures (causing the pump to short-cycle), waterlogged pressure tanks (losing the air charge that maintains consistent pressure), and control switch malfunctions. When your well pump fails, the symptoms are unmistakable: no water at any faucet, sputtering or air in the water lines, rapidly cycling pressure (the pump turns on and off every few seconds), or a sudden drop in water pressure. Emergency pump failures are stressful because your entire household loses water. Many well service companies offer 24/7 emergency service for complete pump failures. Standard repairs include replacing the pressure switch ($150-$300), replacing the pressure tank ($500-$1,500), pulling and replacing the submersible pump ($1,000-$3,000), and electrical troubleshooting. Submersible pumps typically last 8-15 years depending on water quality, usage volume, and installation quality.

Colorado Regulations for Well Pump Repair

Colorado regulates onsite wastewater treatment systems (OWTS) through the Colorado Department of Public Health and Environment (CDPHE), specifically Regulation 43 (5 CCR 1002-43). Local county public health departments administer permits and inspections under delegation from CDPHE. A site assessment must be completed by a licensed professional engineer or registered sanitarian before a permit is issued. The assessment evaluates soil percolation rates, seasonal high groundwater, and setback distances. Required setbacks include 50 feet from water supply wells, 15 feet from property lines, and 50 feet from streams and water bodies. Colorado's high-altitude conditions, including shallow rocky soils and frost depths exceeding 36 inches in mountain counties, often necessitate engineered alternative systems. CDPHE maintains a statewide OWTS database for tracking permits, inspections, and maintenance records. Operations and maintenance plans are required for all alternative treatment systems and must be filed with the county. Homeowners pumping less than 500 gallons per day are exempt from certain commercial requirements, but all residential systems must meet Regulation 43 design standards.

Licensing Requirements

Colorado requires OWTS designers to hold a Professional Engineer (PE) license or be a Registered Sanitarian (RS) recognized by CDPHE. Installers must obtain a county-issued contractor license and pass a competency exam in most jurisdictions. Pumping and hauling contractors must register with CDPHE and comply with septage land application rules under Regulation 62. Continuing professional education is required for PE and RS renewal every two years. Soil morphology evaluations must be conducted by a licensed soil scientist or PE with demonstrable geotechnical experience.

Environmental Considerations

Colorado's diverse geography creates highly variable soil and groundwater conditions for septic system performance. The Front Range urban corridor features clay-heavy soils with poor percolation that often require mound or drip irrigation systems. High-altitude mountain counties experience frost depths of 36 to 48 inches, requiring insulated system components and freeze-resistant designs. Eastern plains soils are sandy loams with good drainage but proximity to the shallow Ogallala Aquifer demands careful siting. The state's semi-arid climate (12-17 inches annual precipitation along the Front Range) limits soil biological activity, slowing treatment. Wildfire-affected areas face accelerated runoff and erosion that can compromise drainfield function.

Signs You Need Well Pump Repair

  • No water at any faucet in the house
  • Pump runs continuously without building pressure
  • Pump cycles on and off rapidly (short-cycling)
  • Sputtering water or air in the lines
  • Sudden drop in water pressure throughout the house
  • Unusually high electric bills (pump running constantly)

The Well Pump Repair Process

  1. 1 Diagnose the failure β€” check electrical supply, pressure switch, and pressure tank
  2. 2 Test the well pump motor for electrical faults
  3. 3 If pressure tank is waterlogged, replace or recharge the air bladder
  4. 4 If pump has failed, pull the pump from the well using specialized equipment
  5. 5 Install new pump at the correct depth with new safety rope and wiring
  6. 6 Test system operation, verify proper pressure range and cycle times

Frequently Asked Questions β€” Well Pump Repair in Colorado

How much does well pump replacement cost?
Well pump replacement costs depend on well depth: shallow wells (under 25 feet) with jet pumps cost $800-$2,000, medium wells (25-150 feet) with submersible pumps cost $1,500-$4,000, and deep wells (150-400+ feet) cost $3,000-$8,000. Additional costs include pressure tank replacement ($300-$1,500) and electrical repairs ($200-$500). Total project cost including all components runs $1,200-$5,000 for most homes.
How long do well pumps last?
Submersible well pumps typically last 8-15 years, while jet pumps (shallow wells) last 4-10 years. Lifespan depends on water quality (sediment accelerates wear), cycling frequency (undersized pressure tanks cause rapid on-off cycling that burns motors), and installation quality. If your pump is over 10 years old and showing any performance decline, budget for replacement rather than repair.
What are the signs of a failing well pump?
Watch for: sputtering faucets or air in the lines (pump losing prime), gradually declining water pressure over weeks (worn impellers), higher electric bills without explanation (struggling motor draws more power), pump running constantly without shutting off (pressure switch or bladder failure), rapid clicking from the pressure switch (short cycling), and sand or sediment in the water (pump dropped or well screen deteriorated).
Should I repair or replace my well pump?
Repair when: the pressure switch has failed ($150-$300), the pressure tank bladder ruptured ($300-$800), or wiring was damaged ($200-$500). Replace when: the pump is over 10 years old (another failure is imminent), the motor burned out (rewinding costs nearly as much as new), or water production has significantly declined (worn internals cannot be rebuilt economically). Never accept a full replacement quote over the phone without on-site diagnosis.

Find Well Pump Repair in Colorado Cities

Browse 2 cities in Colorado for well pump repair providers.

Other Services in Colorado